HeatShield Chimney Liner & Rebuild Nationwide

HeatShield Chimney Liner & Rebuild in Long Beach: What to Know First

HeatShield chimney liner repair and rebuild in Long Beach runs between $900 and $2,800 for most homes we see, with full liner replacements landing closer to $2,200 to $4,500 depending on flue height and access. Turnaround is typically one to two days on-site once we’ve scoped the flue. We’re an independent HeatShield service provider, not a factory branch, and we’ll tell you plainly whether the liner can be saved or needs to go.

Call (631) 378-3317

This page is for Long Beach homeowners who already have a HeatShield liner or cerfractory coating in place and want straight answers about repair, rebuild, or replacement. Wendell Pike and his crew have worked chimneys along West End Avenue, the canals, and the older bungalows east of the LIRR for years. Call (631) 378-3317 and a live person answers.

How HeatShield Products Fail - and How We Fix Them

• HeatShield Cerfractory Flue Sealant coating delamination on older tile liners. The sprayed cerfractory material bonds well to clean clay tile, but on liners that were already spalling or had hidden moisture in the joints, we see it lift in sheets within three to five years. We’ve opened more than a few Long Beach flues where the coating peeled back like old paint because the original tile underneath was never stabilized. Fix: grind back the loose material, assess the tile, and either re-apply after proper surface prep or stop recommending cerfractory altogether if the tile’s too far gone.
• Joint failure at the first and second flue tile from the top. This isn’t unique to HeatShield, but the freeze-thaw cycling off the Atlantic hits Long Beach chimneys hard. Water gets into the crown, sits at the topmost joint, and the sprayed liner can’t hold a seal when the tile itself shifts. We see this on HeatShield jobs every winter. Fix: rebuild the top courses, address the crown, and only then re-line.
• HeatShield’s epoxy cerfractory thinning on unlined brick flues. On older Long Beach homes where HeatShield was sprayed directly into an unlined brick flue, we see thin spots after five to eight years, especially where the flue bends or narrows. The material was never designed as a structural liner. Fix: install a proper stainless liner (we carry DuraFlex and Gelco as backups when HeatShield coated systems aren’t salvageable).
• Stainless HeatShield-branded liners showing corrosion at the tee or cap connection. The liner itself holds up, but the connection hardware takes a beating in salt air. We replace more caps and tees on HeatShield systems in Long Beach than we replace liners. Fix: upgrade to marine-grade cap hardware and inspect the connection yearly.
• Improperly sized HeatShield liners from previous installs. We can’t count how many times we’ve scoped a flue in Long Beach and found an 8-inch liner stuffed into a firebox that needs 6 or a 6 in an appliance that drafts poorly because it’s undersized. The liner brand wasn’t the problem. The sizing was. Fix: measure properly, and if the liner is sized wrong, replace it rather than patching around the issue.

Our HeatShield Chimney Liner & Rebuild Process

1. 1
   Call and talk to a person. You call (631) 378-3317, we answer, and you’ll get an honest conversation about what you’re seeing. No script, no call center. Wendell may well be the one on the line.
2. 2
   We scope the flue with a camera. Every HeatShield job starts with video inspection. We show you the footage and explain what it means in plain English. The number comes before a single tool comes off the truck.
3. 3
   Parts decision: OEM or quality aftermarket. We source HeatShield components directly when available, and we’ll tell you when a DuraFlex or Gelco liner does the same job better for less. Warranty-safe practices on every install.
4. 4
   The repair or rebuild happens on-site. We protect the home, contain the dust, and do the work. Most liner replacements finish same day. Full rebuilds run one to two days.
5. 5
   Draft and pressure test before we leave. We don’t call a job done until the flue draws correctly and holds a smoke test. You’ll see it with us.
6. 6
   90-Day Done Right Promise in writing. If anything’s not right, one call brings us back. No charge, no arguing.

What HeatShield Chimney Liner & Rebuild Costs in Long Beach

Here’s what we actually quote in Long Beach for HeatShield work, not a national average that doesn’t apply:

• HeatShield coating repair (partial, small area): $900-$1,400
• Full flue cerfractory resurfacing after prep: $1,800-$2,800
• HeatShield liner replacement with stainless (DuraFlex or Gelco): $2,200-$4,500
• Partial rebuild (top courses, crown, first tiles): $1,500-$3,000
• Full chimney rebuild above the roofline: $4,000-$8,000

What moves the price: flue height, roof pitch and access (some of those Long Beach three-story waterfront homes need scaffolding), condition of the existing masonry, and whether we’re saving the liner or replacing it. We quote upfront, in writing, and the number on the estimate is the number on the invoice. Call (631) 378-3317 for a free estimate.

Why Long Beach Homeowners Call Top Hat Chimney for HeatShield Work

Wendell Pike started Top Hat Chimney in 1999, and he’s been working Long Beach long enough to run into clients at the hardware store and ask how the fireplace held up through the last nor’easter. We’re not a franchise that rotated in last spring. We publish our address and license number. Wendell puts his name on the work.

Every job gets the 90-Day Done Right Promise in writing. If it’s not right, one call brings the crew back. We carry HeatShield, DuraFlex, and Gelco so we’re not married to one manufacturer when a different liner is the better call. And we tell you when work can wait. If it doesn’t need doing, we’ll tell you that too.

FAQs